DodgeRam.org > Main > Tech > Maintenance > Fuel Level Sender Repair (Huey Conway)

 Simple Ram Fuel sender Repair

Visit Geno's Garage
for Truck accessories.
Geno's Garage Truck Accessories

Originally Posted by Huey Conway
(now posted here because that link is dead)

Out of all the posts that I have read regarding the fuel tank-sending unit I was wondering if anyone has taken a look at its design. Mine went out and I replaced it myself, was not too hard to do. After I replaced it with an identically designed item I took the old one and found out what contributes to the failure of this part. I will try to explain it and a possible fix. The plastic pivot arm is held in place on the metal stem by a plastic tab on the rear edge that wears on the main body of the unit. This wear allows the contacts on the arm to leave the contact on the resistor that sends the signal to the gauge. Result is the fuel gauge no longer works.

Either the fuel tank must be removed or the bed of the truck needs to be moved back for access to the fuel tank module. The fuel lines are removed by pressing on the tabs of the connector while gently pulling on the fuel line. Both lines are removed this way. The connector stays on the line going into the module. They are different sizes so when you reinstall them they can not be crossed up. The electrical connector is removed by using a small screwdriver prying sideways and removing the red clip that locks it in place. On the front of the connector, the module side, there is a tab that needs to be pressed down to unlock the connector and then it is removed by pulling on the connector not the wires towards the frame. Remove the rubber hoses that go to the fuel filler neck and slide them up on the filler neck tube to get them out of the way. There are two nuts holding the fuel tank straps, remove these while supporting the tank with a floor jack or anything suitable. Slowly lower the tank and pull it from under the truck. The module can be removed by gently tapping on the ears of the retaining nut, with a hammer and punch, in a counterclockwise direction, making note of its position for reinstallation. Take care not to damage the rubber seal under the nut as in can be reused.

I noticed on the module, there are three screws that were showing some wear on the slots that attach the lower part to the upper part. I used three washers that would fit the shoulder of the screw to reattach the lower part to the upper part so it would not slide. I measured the nearly empty tank where the module is installed up to the neck where the retaining nut is including the rubber gasket and made the module the same length. My measurement was 14 5/16". I could not figure out why this needs to move up and down. In fact this caused a hole to be chaffed on the return line in the center of the module. Thank goodness it was not the pick-up line I would have had to replace the whole module $400 I think. With an empty tank the module will be touching the bottom of the tank but when the tank is full it will be pulled away with the weight of the fuel.

Now for the suggested repair action.

 
contact.jpg (11457 bytes) The plastic pivot arm has a center stem that extends above the outer body about 1/8". Remove the pivot arm by carefully prying between the main body and the rear part of the pivot arm where the tab is.
contact1.jpg (8654 bytes)Trim the top of the center stem of the pivot arm level with the outer body, with a sharp razor, taking care not to break it. While the arm is off you may want to gently bend the contacts out away from the arm as to allow for better contact with the resistor. Reinstall the pivot arm by carefully pressing it back on the metal stem make sure the holding tab is behind the tapered edge of the main body where it is held on.
Before repair
sender.jpg (21309 bytes)
After repair
sender2.jpg (27586 bytes)

Side View

sender1.jpg (15312 bytes)

Place a Teflon washer on the metal stem with a P-nut, one of those push on washers that lock when installed. Make sure you push the P-nut down far enough to prevent the contacts from loosing its contact to the resistor, taking care not to allow the pivot arm to bind, you can use a small socket to do this. This will allow the weight of the float to be placed on the Teflon washer and P-nut instead of the tab on the rear part of the pivot arm. The metal stem diameter measures 3/32". The float arm can be easily removed from the pivot arm by pulling it away from the arm on the contact end and out over the center stem, then when done reinstall after you are done.

I would like to mention C. J. Johansson, which his suggestion was to manufacture a new pin and machine, threads on the top and use two nuts to lock the pivot arm down on the resistor. His repair and pictures are http://www.chesco.com/~rosenberry/diesel/diesel.htm his pictures are very clear and show the center part of the pivot arm that I trim off. Thanks C. J.!!!

Install the tank in the reverse order you removed it. Making sure the module-retaining nut is positioned in the same place it was removed from. Fill her up and check for leaks!

This should be a better fix than replacing a $42 dollar part each time your gauge quits.

I have available kits that include the Teflon Washer and the P-nut.  These can be obtained for $3.00 shipping and handling along with a SASE, contacting me at mudbone66@hotmail.com for details.

Just my 2¢ worth.

Huey C
Huey L. Conway, Jr.
96, 2500SLT CC Cummins 5spd/3.54 100k
4k "Timbren" load boosters K&N


TOP HOME